Wonderful Ski Vid…

Kudos for this one…  Thanks to Rory B for his flying and MSP for their kick ass edit and camera work…  Sure is purdy.

These are the guys who shot the film.   Pretty amazing stuff.

Patrick Ramano to Speak at RAF STOL Seminar…

If  you are new to backcountry flying or fly a trike, this might be a good seminar to take!

 

Romano_2

Great Article and New Film: STOL Tips (Tricycle Gear Airplanes)

Patrick Romano of Backcountry Aviation has released a great new STOL Tips film along with a detailed article over on BCP.org.   Worth a watch…

 

 

 

Romano

de Havilland Dreams…

Nice…

 

Intermountain Airlines – North Slope & More…

Stumbled on this this AM…

 

Flying Alaska…

Year With North River Air…

“Death Flies Faster” Shirts Are In!

DFF_hoodieWeb

I took the new Bushwagon East graphic and had some swag made…  Available over on AVThreads, men’s T’s and some super cool hoodies.  As always, free shipping to anywhere in the US, and $15 flat rate shipping to Canada.

“Death Flies Faster” is about keeping your ego in check. No matter how good we get or how much we train its a reminder that we can’t outrun everything!  The hoodies are by far my favorite of all the garments I have done. (super limited run of hoodies…) Grab em before they go.

DFF_Grey_T

DFF_Sweatshirt_Blue DFF_shirt

 

 

 

Wing X Install – Part 5…

Orig published over on BCP.org March 2015…  This article is for entertainment only and is NOT an approved or instructional material.  Consult the proper installation documents for reference.

ebb72184a4e3e43508bd4f50

The install continues…

A word about pulling the rivets. Although the kit comes with everything you will need (and some extras for once) it’s always good to understand just WTF is going on. The stainless strap uses Cherry Max and not just cherry rivets. If you and (God forbid your AP) don’t know the difference, its worth learning.

5a72e5efb9600761f1965465

Before you move on, make sure all the rivets lock. In a nutshell, the stem gets pulled and must lock with the steel collar. If it doesn’t, the rivet will not look flush, and if its not flush, its not structurally sound.

095ceaceae6ce4f9dd6ae6b7

Next step is to dress up the outboard ends of the upper lift strut. Because flush rivets were removed and universal heads were installed, you will have to dish out some material on the inboard and outboard side of the strut in order for the strut to fit back where it belongs… A bit nerve wracking at first, but no biggie as you will be working distal of where the tangs rivet to the strut. Dremel works great here, first with the cutting bit, then the sanding drum.

72ff56d81f0450769dba5bd5

 

d44edad6ed44ed2792a23a14

0c3c17bd8b9903eb17c1edbd

Remember to measure sixteen times and cut once… You can always remove material, but never add it on.

61d1df316136179dd5e1c67c
Last thing you might want to think about here before you re-install the lift strut is to rehab the tangs. I cant in good conscious re-install a part without freshening it up, so I hit it the part with some scotch bright, z-chromate, and some metal finish Rustoleum.

a7eb560cec7e4a22248842b3

5fba245129994c0dcb4fb3ba

Wing X Install – Part 4…

Orig published over on BCP.org March 2015…  This article is for entertainment only and is NOT an approved or instructional material.  Consult the proper installation documents for reference.

9d917f8dc7f230be4ddb9cb6

f523d62eb3a752380e51c504

Next I focused on the stainless strap. Again, this is getting sandwiched between the skins at Sta. 100. Note: This step is only required on SOME models. You will have to check your main spar to see if it is needed.

f523d62eb3a752380e51c504

 

930f16ab54b8a761311f2ac1

With the strut out of the way, you can now drill the heads of the flush mount rivets. You will be drilling out the 5’s and installing #6 universal head cherry max. Even though you will be eventually enlarging the holes with a #10 bit, take care not to take the easy way out and just drill out the 5’s. Snap the heads, and drive the tails out with a punch…

c4a02af9d140c082fda1d7fb

With the flushies out, slide the stainless strap between the skins and start spotting. Spot drill, remove, drill press, install, spot drill, remove, etc… Stainless sucks so go nice and slow and take your time.

40f4e33914acd25de3bc8b6a

Once the holes are all in, and everything fits, fit the strap and enlarge the holes with a #10. Remove and debur, then install for the final time….

ac774503ea2ea1f7aa2b9b10

Since clecos wont really pull the sandwich tight enough, I used several #10 fasteners to snug it up real tight. Once you are all set, pull the #6 universal cherry max rivets. The 6’s are damn near impossible to pull by hand, so make sure you have a good pneumatic rivet gun handy.

90896d4da857385b176a7774

One final note… The kit comes with all the fasteners and rivets you will need. That said, make sure you double check the hole with a grip gauge before you pull the cherry Max. The stainless strap will use 6-6’s for all save one. This is where the skins lap. Here WingX provides a 6-7.

77a457855ec4a1af28c5fab1

Wing X Install – Part 3…

Orig published over on BCP.org March 2015…  This article is for entertainment only and is NOT an approved or instructional material.  Consult the proper installation documents for reference.

 

867649e2bf4830a57592944f

Next on the agenda is to get the strut out of the way so you can gain access to the Sta 100 lower rivets.

I use a Genie Superlift as it is perfect. Its manual crank allows for very small adjustments and its fork is just wide enough to lay a small cradle on and grab the outboard wing. It is also perfect for lifting the TW to get A/C into flight attitude for weighing, fuel calibration, or whatever… Once you have the bolt loose, releave the tension and drive out the bolt with a brass drift. It’s tough to get a hammer on the drift, so if you can’t get the bolt totally out, careful not to cheat and ease it out with a ratchet… This will gall the inside of the fork and weaken it.

1f7c99e68dca5ade21d445fa

7be46d5698379bf7a35d2d9b

It’s a bit freaky, but crank the wing up just enough to let the strut end drop out. With the strut free, lower it just enough to gain access to the rivet line.

7d6214b0afb9f30333b37c09

Nice Article on Flying Iceland Up on BCP…

Article by By | 29 February 2016.  Click HERE to read.

Screen Shot 2016-03-01 at 10.20.23 AM

Wing X Install – Part 2…

Orig published over on BCP.org March 2015…  This article is for entertainment only and is NOT an approved or instructional material.  Consult the proper installation documents for reference.

db2ab4f15cb32406437b126e

Lots of places to start, but the first step I did was to cut the access holes in the underside of the wings. The instructions say you can cut as many as needed, but really the job can be done with just two in the right spot. This is not a how-to, so confirm your own measurements, but the holes are roughly inboard of Sta 136 and 154, 2nd bay aft of the forward spar.

To cut the holes, I used the ARC360 from Spruce which is totally awesome. Super easy to use, fast, and perfect holes. No muss, no fuss.

9cdc0fea0c0b49d0d356eb22

9ae90b4e160883dcb5047236

4553f3c837c939aac7f10929-1You may want to rivet the backing plates for the inspection covers at this stage, but don’t squeeze em yet as you will want the holes as large as possible to get your arms in there… and for that, make sure you wrap some tape around the edges of the holes to save your forearms from getting all cut up.

96219964cd3dc5ba72a835c4

3238132a1b6c2d568ec3ab7f

 

 

Dead Stick Landing – C170B…

This is an oldie but goodie.  Nice job by the pilot.

Wing X Install – Part 1…

Orig published over on BCP.org March 2015…  This article is for entertainment only and is NOT an approved or instructional material.  Consult the proper installation documents for reference.

dde3ad627e3157becf38cc03

Alright… The Wing-X.

First thing to talk about is just WTF is this all about. Most 100 series Cessna owners knows about it, but exactly what is involved can be a bit of a mystery as there isn’t much install info on the web. One thing is for sure… it’s damn expensive. At $5k for the kit alone, its no joke. A shop that has done em before is in for 40-45 hrs while a first timer may be in as much as 60.

The WingX website claims the additional 12 sq feet will give a 25% reduction in ground roll (on wheels,) a 12-15% increase in climb performance, 1000′ increase in service ceiling, and a GW increase.

WingX

All sound good, so lets do it right?

Bummer is for me, I already put the big stab and Kenmore GW increase on, so nothing there… Increased T/O roll sounds nice though… An easy take off in the wagon is 250-300′, but any decrease is welcomed. A really good crisp cold day with light fuel is about 1700’/min so another 200’/min might be real nice indeed…

Kenmore

For the most part, the general consensus seems to be that for floats, the kit is for sure a winner. For wheels, it gets a bit more convoluted. I’ve tried to do the research, and unfortunately the “been-there-done-thats” that I trust generally say not to install it. I’m not sure if this is because they say it its tough in the x-wind, a bitch to get to stop floating/flying, or just damn near impossible to get inside a regular hanger, but because I own the kit, AND its super easy to take off once the install is done, I’m gonna put the damn thing on and make up my own mind.

You can order it for the stock wing, or as in my case, for the Sportsman. I did test fit the kit while I was doing the Sportsman install and the fit is pretty snug. Paul from WingX and Willie Stene work very closely and have worked out all of the bugs, so I expect no issues due to mod conflicts.

Here goes….

6aeddc900a701fd685c05c5a

First understand the kit breaks down into three basic steps.  1) The stainless strap, 2) the packer, and 3) the tips.  If applicable to your A/C

The stainless strap is used if your A/C does not have the later beefier angle bracket at and around Sta 100 and if you want or are operating above a certain GW. This strap is centered at Sta 100 (just under the strut) and is stuffed under the leading edge skin trailing edge. The bitch here is you will have to unload the strut by lifting the wing and then move it down about 12″. It also sucks ass to drill the stainless… But not impossible if patient. Go slow, and have some extra bits handy. The packer is fitted using #6 universal head cherries so make sure you have the proper pneumatic puller.

e6e2a18455bb1e784ac9b9b9

The packer is made up of two bits of alum straps that are riveted up under the forward spar cap centered around Sta 136. These are aluminum and much easier to drill, but require some modifications to the ribs to get them to fit.

You will need to cut at least two new inspection ports in two bays to gain access to buck the rivets. The Wing-X drawings are God awful, don’t follow standard A/C convention, and have a bunch of confusing illustrations (e.g. large views of the left wing with exploded views of the right.) Might take an experienced sheet metal worker a couple of head scratches and some time to sort it all out, but in the end, it ain’t rocket science. Actually being smart might be a detriment as I’ve seen the less experienced A&P just push thru this install w/out asking the important questions. Their installations aren’t pretty, but they go quickly.

Regardless, I will say that Paul C at WingX is FANTASTIC and will be there (even on the weekend) for support. Top notch customer service IMO. Although confusing, he provides a good and complete kit.

fcb5085e5677019b89af04a9

Last of the three components are the wing extensions.  These come primed and will eventually just screw on like wing tips. Patience here is important as it is fairly critical to get the geometry perfect.

4bb7e77f782b826b0ee0d93a

More tomorrow…

Wing-X Install Begins…

Post was orig published over on BCP.org Feb 2, 2015...

Well we have been slammed with snow here in New England… Just got our hanger plowed out yesterday in time for another 12″ of the stuff today…

b3cc4e3111f29c0c0a43ea2f

Anyway… The non-flying WX is good for projects, so I thought I would start in on the Wing-X install.  I’ll try to do a detailed install report, so stay tuned!

2e147f3a13f51644ea910483

 

Already Missing My Penny’s…

Vid from Chris Wall.

Leaky Bladders…

DSC_3344

If you haven’t heard, probably the least loved task to do on a Cessna Skywagon is replacing bladders.  Fortunately for me, I was happily tapped by fate to take this dive after springing a leak.

Since I started on the resto of the Wagon, I knew that I was going to have to face this at some point, but have been pushing and pushing it off until finally my number was up.

My 66 has extended tanks, which is both a blessing and a curse.  Curse because the tank is bigger.  Blessing because there are two ports to allow just a bit better access.

IMG_0917

First step is pull the bung and drain all the fuel.  (This is a great time to order new sump drain valves and stainless steel safety wire screws)

Next, pull the ports and caps.  Also a good idea to order new stainless fasteners here as well.  On my airplane, the large machine screws are MS24694C48, the small ones are MS24693C293, and the stainless safety wire screws for the drain are AN500AD8-7.

Be very careful removing the screws as chances are they are in there good and solid.  Get some penetrating oil on and let them soak overnight.  Use the CORRECT screwdriver, and take your time.

If your unlucky enough to round out the well, don’t fret as you can use a Dremel and cutoff wheel to carefully make a slot in the head for a regular screwdriver.  Takes practice, but doable without getting into the surrounding alum.  (Just make sure there are no vapors kicking around!)

DSC_3240a

With the caps out, a good idea is to line the edges of the cavity with duct tape to protect both the tank AND your arms.  You will thank me later…

DSC_3258a

With the caps out, take your time and remove all fittings.  This will be fuel outlet screens (forward and aft in later models) crossover vent, fuel sump, fuel sending unit, and outboard vent.

The fuel outlets are the trickiest because they are delicate.  Once out, it’s a good time to give em a real good inspection.  Although not always possible, I am a big fan of replacing parts with new.  The problem with these screens is (like everything) Cessna wants an ungodly chunk of change… Have a late mode bird and you have now doubled that ass raping cuz you need two.

The good news is that Burl’s Aircraft in AK has a fantastic solution.  Their STC’d spun aluminum screens are not only cheaper, but they provide a much better flow rate.  Worth checking out!

DSC_3246

Anyway… reach in the cavity and roll the bladder into a nice tight sausage, and then CAREFULLY work it out the port.  This part sucks for sure, but enjoy it cuz getting her back in will make this part feel like cotton candy and prancing unicorns.

IMG_0721

With the tank out, get her in a box and ship her out.  There are two big places to send out the bladder.  Although their website is cerca 1990, I have had great luck with the service from Heartwig.  Eric is a good dude and worth a phone call.

heartwig

If you weren’t having fun yet, strap it on…

Lots of AP’s lazy-out here because when it comes down to it (you know who you are,) it’s really tough to send the customer a bill for all the time it actually takes to clean and prep a tank bay.  But if you want it done right, make sure you take your time and get it clean enough to eat off.  (Took me 9 hrs of labor to remove tape & clean.)

IMG_0732

Start by pulling the old tape that you can grab.  Heating it up with a heat gun makes this a bit easier and if your lucky, you will be able to get most out without falling into small strips.

Once the tape is off, you will be left with the dried glue.  I find that the best solvent to get this stuff off is called “Goof Off.”  Stuff works fantastic, but a real killer… so make sure you have good gloves and a solid respirator.

 

DSC_3239

DSC_3227

Now that you have cleaned the bay, you can start laying in the new tape.  The point of the tape is to protect the bladder from chafing on corners and rivet heads.  Some think that you can just use Duct tape, but this is not the case.  Tell Eric at Heartwig you need a roll, and he will provide you with one on return of the bladder.

DSC_3276

Laying the new tape in perfectly is next to impossible, so don’t get too bent if it isn’t 100% pretty.  Just take your time, and do your best.  If you did a kick ass job with the prep, the tape will hold solid for another decade and the next guy wont shake his head at you when he gets back in here.

Sometimes they are too far gone, but with some luck, Heartwig will be able to repair the bladders.  They will come nice and shiny and oiled.  If you can, put the bladder in a heated room overnight to get it nice and playable.  You will also want to crank the heat in the hanger.

DSC_3263

Lay out the bladder, roll it up into a sausage again, and start sliding it in.

Once in, lay it flat and start asking Job for patience.  First, connect the snaps (bottom of the tank) to their position in the corners.  Once you have these, patiently work the top fittings, getting the furthest ones first.  Ain’t gonna candy coat it… this really blows.

Truth be told, this isn’t the hardest thing to do, but there is no doubt that this is the most trying task one can undertake.  All I can say is know it can be done.  You don’t need to take the damn wing off, remove any ribs or skins… Just take your time, don’t get frustrated, and motor thru.   Oh… and if you have short arms your F’d.

With the bladder in and all the snaps fitted, go ahead and reconnect all the plumbing, caps, and sending units.  Make sure you use NEW gaskets!  If you are really progressive, you might think about installing new McFarlane fuel sending units here, but I guess I should remember how easy it is for me to spend your money on the interweb.

sendingUnits

If you don’t have a good torq wrench, make sure you pick one up.  It’s always critical, but here, an overzealous wrist can cause a leak pretty fast… And that blows.

DSC_3286

 

At any rate, that’s a quickie on Wagon bladders.  Good luck!

 

 

New Artwork…

Created some new artwork for Bushwagon East.  Shirts and stickers have been ordered… They will be available in the AV Threads shop soon!

shield

Backcountry Safari Flix…